Mastercam Tool Library Generator Utility

Mastercam Tool Library Generator

For enhanced functionality, enable JavaScript in your browser and allow pop-up windows and cookies.

Default Language

This will save a cookie with your language preferences. If no cookie is found or the cookies are disabled, the default language will be English.

Default Save Directory

The library generator must know where you keep your Mastercam files. Otherwise the generator will use either previously saved cookie value, or it uses the library generator default.

Write or copy-paste your default directory here.

Press this button to save the directory setting into your browser cookies. JavaScript and cookies must be enabled.

Tool Features

If you do not want to set different values for your tools, mark the checkbox. (You must have JavaScript enabled.)

Tool Selection

Select which tools you want to create. You can show/hide tools by clicking on checkboxes. (You must have JavaScript enabled to toggle show/hide.)

Create tool: Drill (3)
Create tool: Reamer (6)
Create tool: Flat End Mill (10)
Create tool: Ball End Mill (11)
Create tool: Face Mill (13)
Create tool: Dovetail (16)
Create tool: Taper Mill (17)
Create tool: Bull End Mill (19)

Drill (3)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Reamer (6)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Flat End Mill (10)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Ball End Mill (11)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Face Mill (13)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Taper Angle	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Dovetail (16)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Taper Mill (17)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Bull End Mill (19)

First Tool Number	Tool Material	Retract Rate

Tool name

Selected	Tool Diameter Range mm		Step mm	Flutes	Corner Radius	Cutting Speed	Feed per Tooth
		—
		—
		—
		—
		—
		—

Contact Information and Terms of Use

E-mail: np [@] iki . fi

Terms of Use

This web-based Mastercam Tool Library Generator software was created by Suomen Postmaster.

The software is provided on an "AS IS" basis, without warranty of any kind, including without limitation the warranties of merchantability, fitness for a particular purpose and non-infringement. The entire risk as to the quality and performance of the software is borne by you. Should the software prove defective, you assume the entire cost of any service and repair. It is strongly advised to double-check all the tool libraries you create using this software. Otherwise you may risk damaging your tools.

Suomen Postmaster does not provide tech support on tools you create on your own, unless specifically contracted to do so.

You are free to use this tool to generate as many tool libraries as you like at no cost. However, if you wish to make a PayPal donation to us, you can use the link below.

Program version: 0.96 - 2010-03-20.
E-mail: np [@] iki . fi
Address:
Suomen Postmaster
Mr. Niilo Paasivirta
Keskisentie 3 C 34
40520 Jyväskylä
Finland
GSM: +358-50-340 54 59

This is a dummy button. It does absolutely nothing. :( Maybe very soon it allows you to click it and make a donation! Which would be very nice!

This generator has been tested with...

Firefox 3.5
Google Chrome 4.0
Internet Explorer 8
Opera 10.50